The Blomberg washing machine is an example of German build quality. These are reliable cars that are on a par with the leading brands in Europe.
All modern Blomberg cars have a self-diagnosis system. Its main function is to search for possible malfunctions and failures, notifying the user about this.
Fault codes are displayed on an electronic display. In older models, indicators in different sequences flash on the panel.
If the Blomberg washing machine has served you for many years, and now gives an error, the main thing is to figure it out. In the table below, we will consider the common Blomberg error codes, which means their appearance, how to troubleshoot.
Blomberg washing machine error table: what it means, how to eliminate
Malfunction code | Decryption | Reasons, elimination |
D01 | Error d01 lights up on the display when no water enters the machine. | This is due to a malfunction in the water intake system. There may be no water in the water supply or too low pressure. Clogged inlet hose or filter. Damage to the solenoid valve is also likely. In more severe cases, clogging of the filler pipe is possible. |
D02 | If d02 is displayed on the SMA display, then there is a problem with draining the water. | To understand how to fix a breakdown, you need to find its cause. This may be a blockage in the drain filter, water drain hose or drain pipe. Breakdown of the drain pump (pump) is not excluded. |
D03 | If the d03 error lights up on the SM screen, then the water does not heat up in the machine. | The cause of this failure may be the heater. If the heater is overgrown with scale, then heating of the water does not occur. TEN could burn out or short to the case. It is necessary to disassemble the case, check the heater and, if necessary, replace it. |
D04 | If the machine shows error d04, the triac could burn out. | In the event of a short circuit, the triac needs a replacement. |
D05 | Blomberg shows error d05 on the display if NTC (thermistor) is broken. | Need item replacement. |
D06 | With error d06, there is no tacho signal. | You may need to check the wiring to the tachogenerator, or replace the tachometer. |
D07 | The washing machine gives the code d07 when there is no signal that the hatch door is locked.
| Try to cover the hatch more tightly. If this does not help, you will need to replace the lock (UBL). |
D09 | Broken selector for washing program. | Replacing selector or wiring required. |
D10 | Water overflow detected in the tank. | To remove the error, it is necessary to replace the water intake valve or repair the control unit. |
D11 | The electronic unit does not see the water heating circuit. | With error d10, the heater, control board (unit) or the water heating circuit can be broken. |
D13 | There is no spin of linen. | What to do: try to take away part of the laundry. Damage to the engine or control unit is also possible. |
Other Blomberg Washing Machine Error Codes
In some models, the failure codes are different, we will also briefly consider them:
Breakdown code | Code value |
H1 | What does the H1 code mean? Usually it is displayed when the hatch door of the washing machine is not tightly closed. |
H6 | Code H6 indicates a drive problem. Perhaps the belt just slipped off the pulley and it would be enough to fix it. Or the pulley, engine, or maybe the drive belt is worn out. |
H12 | Blockage of the Aquastop filter. |
ER7 | ER7 also indicates a problem with closing the sunroof. |
You can also try to reset errors by rebooting the wizard:
- Disconnect the machine from the network.
- Wait 10-20 minutes.
- Turn on.
If the error disappeared and did not appear anymore, perhaps it was just a “glitch”. But if the code reappeared on the scoreboard, the problem was confirmed, and you need the help of a specialist.
Often you can find a solution to your problem yourself by looking at the user manual or in our useful articles.